1/10 Scale Electric Rally/Touring Car:

Team Associated RC10R5 Factory Team - Radio Controlled Model

Navigation:

History and Information for the RC10R5 Factory Team:

Released by Team Associated in 2008, the 2WD RC10R5 Factory Team GT Racing Chassis kit - # 8020 - was optimised for brushless motors.

The 10R5 FT graphite chassis, came with coil spring over oil filled through shaft damper, ball differential and a full set of ball bearings.

Team Associated RC10R5 Factory Team - 1:10 Electric On Road Car

▼ Scroll Down for More Images ▼

To race the Team Associated RC10R5 FT, you need to tweak and adjust all you can to give your car improved handling, stability and grip to ease around the curves and keep you on the track. One little setting change can transform your car into a world beater. Just follow our chart to attain the most favourable Set-up to suit your particular needs on any track.

RC10R5 Factory Team - 8020
Manual

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ Team Associated RC10R5 FT Chassis ★

Buying a Used Team Associated RC10R5
Touring Car (and What to look for)

There are essentially three reasons you might want to buy a used Team Associated RC10R5 Electric Touring Car; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Associated website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Team Associated Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Team Associated models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Team Associated RC10R5 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your RC10R5 model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your RC10R5 Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

The gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The RC10R5 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Team Associated RC10R5 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Team Associated Touring Car came with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your RC10R5 model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Choosing a Transmitter

   When you first started in RC, you may have purchased a package that came with the car kit, motor, battery, charger, ESC and radio system complete. The transmitter was probably just a basic steer wheel, or stick type, with nothing more than forward, reverse, left, right and simple trim settings to centralise the servo and ESC.

   After a while, as your enthusiasm grows and your experience increases, you will want to move on to a better radio system, with more setting options, but where do you begin?

   Choosing the right transmitter is a personal thing. It has to feel right, have the balance you like, not be too bulky for your hand size and have all the features you might need to set up your car to your driving style.

Read the Complete Article ▶ ▶

Hints, Tips and Information

Radio Frequencies - be Careful be Safe

   After buying your first car, it won't be long before you need more than simply bashing around the back yard, or out on the street. So you will be looking around to find a club that is not too far away where you can do some serious racing.

   Before you can start racing, you will need at least three different sets of crystal frequencies. The race organisers will note down all your available frequencies when you register at the track and allocate one of those frequencies to you for your heat. To avoid change over problems from one heat to the next, they generally try to give you a frequency that no one in the heat before or after is using, but always check to make sure before you put your car down on the track and switch on.

   There is nothing more annoying than to be in the middle of your best qualifying race and some idiot switching on their transmitter in the pits, on your frequency. Not only could it spoil your race, but it could cost you a lot of money if at the time you are travelling at top speed along the straight, loose control and crash head on into the wall.

Read the Complete Article ▶ ▶