1/10 Scale Nitro Truck/Truggy:

Team Associated GT2 Factory Team - 7080 - Radio Controlled Model

Navigation:

History and Information for the GT2 FT:

Released by Team Associated in 2006, the 2WD RC10GT2 Factory Team Nitro Truck kit - # 7080 - came with the new "Posi-Lock" quick-change rear wheel system.

Based on an alloy plate chassis, the model employs a ball differential, coil spring over oil filled dampers, universal joint drive-shafts and a full set of shielded ball bearings.

Team Associated RC10GT2 Factory Team - 1:10 Nitro RC Truck

▼ Scroll Down for More Images ▼

To race the Team Associated GT2 FT, it must be fine tuned to improve handling, provide responsive steering and give you the grip to cruise around corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our step by step procedure, will guide you to the best Set-up for your individual driving style.

Model Version:

#7080 RC10 GT2 Factory Team

Features:

4:09:1 ratio gear box
Hi-Torque 2-Shoe clutch
Posi-Lock Quick-Change System
Hard anodized 6061 aluminum chassis with molded kickup
Blue aluminum front bulkhead
Blue aluminum hinge pin brace
Blue tuned muffler and manifold
Rear suspension mounts are keyed to the chassis for maximum strength and consistent settings
Easy-to-remove radio tray
Sealed receiver box with embossed AE logo
New easy-to-open 82cc fuel tank for fast pit stops
New a-arm design and material for maximum durability
New heavy-duty steering blocks
Molded front and rear shock towers
Dual bellcrank steering with adjustable servo saver
Vertical ball stud adjustment on both front and rear upper link
New rod ends with aluminum pivot balls

(Source: Media Press Release.)

RC10 GT2 - 7080 / 7092
Manual

CHECK AVAILABILITY
On Amazon

RC10 GT Evolution:

Radio Controlled Model Accessories:

★ Team Associated RC10 GT2 Factory Team ★

★ Team Associated RC10 GT2 FT ★

★ Team Associated RC10 GT2 FT Chassis ★

Team Associated RC10 GT2 Factory Team Chassis

★ Team Associated RC10 GT2 FT Chassis ★

Buying a Used Team Associated GT2 Truck (and What to look for)

There are essentially three reasons you might want to buy a used Team Associated GT2 Nitro Truck; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Associated website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Team Associated Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Team Associated models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Team Associated GT2 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your GT2 model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your GT2 Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Nitro Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The GT2 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Team Associated GT2 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Team Associated Truck came with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your GT2 model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Damper Pistons

   When you first build your RC model, you will sometimes find that there are a number of different pistons in the kit, with varying numbers of holes or hole sizes in them. Generally, the manufacturer will suggest one particular piston in the car manual, and may provide you with a mid range oil weight, but depending on the type of terrain you intend to race your model, their suggestion may not be the best for your needs.

   When it comes to tuning your dampers there are basically two things you need to know about pistons. "Pack" and "Static Damping".

   Pack, is the speed your damper reacts to any quick compression and can be considered to be a consequence of the size or number of holes in the piston. Smaller holes, more pack, larger holes, less pack.

   Static Damping is the amount of resistance you sense when slowly pulling or pushing the piston rod in and out of the damper.

Read the Complete Article ▶ ▶

Hints, Tips and Information

Bumpsteer

   In plain language, Bumpsteer is exactly what it sounds like. If your car goes over a bump, it will affect the toe-in setting and can on some tracks make handling of the car in a straight line difficult.

   To check if your car might have any problems with bumpsteer, have it in race mode, with the motor and battery etc in position. Place the car on a flat surface and push down your car at the front. Looking down from above, keep a close eye on the wheels and watch for any angular movement to the side. If there is then you have bumpsteer.

   For off road cars, because of them having longer dampers in comparison to on road, a small amount of toe out is considered by many as acceptable in the lower position and can sometimes be used as a tuning option because of its aggressive effect on turning ability when entering corners. On road cars, because of the shorter damper movement and the greater need for precise steering and stability in a straight line, generally have less of a problem. However if bumpsteer is detected, drivers generally try to eliminate this as much as possible.

Read the Complete Article ▶ ▶

RC Models:

Radio
& Motors:

Other
Accessories:

Buggys
Formula 1
Monster Trucks
Rock Crawlers
Touring Cars
Trucks

Transmitters
Receivers
Crystals
Servos
Electric Motors
Nitro Engines

Batteries
ESC
Tires
Wheels
Bearings
Body Shells