1/10 Scale Electric Truck/Truggy:

Team Associated RC10 T2 - 7012 / 7036 - Radio Controlled Model

Navigation:

History and Information for the RC10 T2:

Released by Team Associated in 1995, the 2WD RC10T2 was available in two kit forms: # 7012 - Sport, or # 7036 - Racing. The model was a completely new design, based on the truck driven by Matt Francis in the 1995 World Championships, but replacing the composite plastic chassis of his truck, with a rigid alloy tub chassis.

Team Associated RC10-T2 - 1:10 Electric RC Truck

▼ Scroll Down for More Images ▼

Basically, the T2 Racing version is based on a black anodised alloy tub chassis, with a ball differential, coil spring over oil filled dampers, slipper clutch, universal joint drive-shafts and a full set of ball bearings. The T2 Sport has the same basic setup, but with dogbone drive-shafts and bushings.

Model Versions:

#7012 RC10T2 Sport Truck Kit, less radio system and battery, with mechanical speed controller, motor and bushings
#7036 RC10T2 Racing Truck Kit, less radio system, battery and all electrical, with ball bearings

Features:

Bulkhead is made of stronger, lighter, composite material
New 2.6:1 reduction Stealth transmission, with Associated Torque Control
Lightweight one-piece racing wheels in fluorescent yellow (three-piece wheels for Sport)
Larger diameter differential increases torque capacity
Universal drive shafts (Dogbones doe Sport)
Ball bearings (bushings for Sport)
Hard-Anodized PTFE coated shocks and PTFE pistons
Suspension arms, front and rear. Improved geometry in composite material
Battery holding system. Allows for 6- or 7-cell packs, as well as stick packs
Front suspension geometry. Improved for more positive steering
Pro-Line XTR compound Edge front and Mini Pin rear Tires
Rear suspension geometry. Improved for better rough track handling
New lightweight Steering servo mounts
Stronger, lighter, stiffer, aircraft-grade aluminum tub chassis. Underside of chassis is angled for body-roll clearance
New, sleek, racing truck body

(Source: RC10T2 Instruction Manual and Magazine Adverts.)

RC10T2 - 7012 / 7036
Manual

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ RC10T2 Box Art ★

★ RC10T2 Box Sides ★

★ RC10T2 Chassis ★

★ Team Associated RC10T2 Black Anodised Alloy Chassis ★

★ RC10T2 Front Shock Mount with hard-anodized PTFE coated Dampers ★

★ RC10T2 Rear Shock Mount ★

★ Team Associated RC10T2 Stealth transmission ★

★ RC10T2 2-piece Motor-Mount and Slipper Clutch ★

★ RC10T2 A-Arms ★

Buying a Used Team Associated T2 Truck (and What to look for)

There are essentially three reasons you might want to buy a used Team Associated T2 Electric Truck; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Associated website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Team Associated Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Team Associated models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Team Associated T2 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your T2 model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your T2 Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Electric Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The T2 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Team Associated T2 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Team Associated Truck came with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your T2 model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Electric Motors for RC Models

Winds and Turns

Q/  What does 15x2 or 17x3 mean?
A/  The first number relates to the number of times the wires are wound round each of the 3 armature segments, the second number relates to the number of wires side by side. So a 15x2 would have 2 wires laid side by side and wrapped around each segment 15 times.

Q/  What is the difference in performance between a Low Turn motor (eg 11x1) and a High Turn motor (eg 27x1)?
A/  A Motor with Less Turns like an 11x1 means high current draw from the batteries which corresponds to less runtime, but More Power (Torque or Punch) Best for tracks with lots of corners and short straights where fast acceleration is needed. (use a small pinion)
Motors with More Turns like a 27x1 give you More runtime, but Less Power. So you get a smoother response and are therefore easier to drive. Better for less experienced drivers and Long straight, sweeping corner tracks. (with a large pinion). This is correct for Brushed, Modified and Stock Motors as well as Brushless Motors.

Q/  How do the number of winds effect a motor?

Read the Complete Article ▶ ▶

Hints, Tips and Information

Shock Mount Settings

The combinations of Shock settings available on the majority of on and off road cars are far too many for this article to cover, so I will endeavour to explain some of the basics, that should give you some idea what these changes might achieve. Some of the settings suggested may not be available on all RC model cars.

If you look at the lower wishbones of you model, you may see a number of holes alongside where the ball studs for the dampers are positioned. If you were to remove those studs on the rear wishbone and reposition them in the hole further out from the center of the car, the first thing you will notice is the ride height has dropped, this can be corrected by adding C spacers above the springs. The second thing you will notice is the shocks are more sluggish, this can be compensated by using thinner oil.

Read the Complete Article ▶ ▶

RC Models:

Radio
& Motors:

Other
Accessories:

Buggys
Formula 1
Monster Trucks
Rock Crawlers
Touring Cars
Trucks

Transmitters
Receivers
Crystals
Servos
Electric Motors
Nitro Engines

Batteries
ESC
Tires
Wheels
Bearings
Body Shells