1/8 Scale Nitro Monster Truck:

Carson Raptor V25 Pro - Radio Controlled Model

Navigation:

History and Info for the Raptor V25 Pro:

Introduced by Carson Modelsport circa 2010, the 4WD Raptor Pro V25 - # 500204023 - came RTR with an engine and radio system.

The model is shaft driven on a twin vertical alloy plate chassis, with gear type differentials, 8 x coil spring over oil filled dampers, dogbone drive-shafts and ball bearings.

Carson Raptor-V25-Pro

▼ Scroll Down for More Images ▼

To race the Carson Raptor V25 Pro, it requires time and patience, to tune and adjust for improvements in handling and steering ability and to get the grip you need to stay on course when manoeuvring around tight, slippery corners. A little can be a lot when it comes to changing your cars settings and our easy methodical directions will guide you to the best Set-up to help you win and keep you winning.

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ Carson Raptor V25 Pro ★

★ Carson Raptor V25 Pro Chassis ★

Buying a Used Carson Raptor V25 Pro
Monster Truck (and What to look for)

There are essentially three reasons you might want to buy a used Carson Raptor V25 Pro Nitro Monster Truck; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Carson website, or purchased separately on eBay. With an instruction manual, any problems with your model Monster Truck you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Carson Monster Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Carson models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Carson Raptor V25 Pro is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Raptor V25 Pro model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your Raptor V25 Pro Monster Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

The gearbox of your used Monster Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Monster Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Monster Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Nitro Monster Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The Raptor V25 Pro steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Carson Raptor V25 Pro is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Carson Monster Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your Raptor V25 Pro model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Look after your Gears

   In RC there are a number of different gear teeth sizes we tend to use, based on two systems. Imperial and metric.

   The imperial system has sizes 24dp, 32dp, 48dp and 64dp. DP stands for Diametral Pitch and the number refers to the number of teeth per inch.

   The metric system has sizes 0.4m, 0.5m, 0.6m, 0.7m, 0.8m and 1m. M stands for Module and is the ratio of the reference diameter of the gear divided by the number of teeth.

   The different sizes are used basically for strength. 32dp gear teeth are larger than 64dp gear teeth, therefore the 32dp gears are by design stronger and for this reason are more commonly used on a number of entry level buggys, to help them withstand the knocks and crashes by drivers new to RC, and nitro models because of the higher torque levels involved. Also, the bigger the scale of the model, the stronger the teeth need to be.

Read the Complete Article ▶ ▶

Hints, Tips and Information

Choosing a Nitro Engine.

   Once you have made your choice of RC model, you need the right engine to get you where you want to be - out in front.

   Touring / Drift Cars: Nitro powered Touring cars require a specific ability. Your first consideration should be the tail pipe. A number of models will take only a rear tail pipe configuration, but the majority will accept the more conventional side pipe.

   Beginners should consider something with a moderate amount of power and a rotary carburettor for easier controlled handling. For top level tarmac track racing or those with more experience, look for an engine with good low end torque that has a slide valve carburettor to give you fast acceleration out of the corners.

   Trucks and Monster Trucks: Unlike on road Touring Cars, Off Road Trucks and Monster Trucks don't need that bottom end torque, unless you like to do wheelies. So something less powerful with a rotary carburettor will provide you with the smooth acceleration and less wheel spin required for controlled dirt track racing.

For other model types read the complete article ▶ ▶