1/10 Scale Electric Sprint Car:

Custom Works Enforcer G6 DD (Radio Controlled Model Review)

Navigation:

History and Info:

Introduced by Custom Works circa 2015, the Enforcer G6 DD, Direct Drive Electric Sprint Car was available in two kit options: Standard Chassis - # 0926, or Centered Chassis - # 0930. Both versions came with a new Roll Cage and Knoxville Sprint Body. A Radio System, Motor, ESC, Battery, Charger and Steering Servo had to be purchased separately.

The 2WD model is based on a carbon chassis plate, with carbon shock towers, a ball differential, coil spring over oil filled MDX V2 dampers, CVD drive-shafts, titanium turnbuckles and a full set of ball bearings.

Custom Works Enforcer G6 DD Sprint Car

▼ Scroll Down for More Images ▼

To get the best from the Custom Works Enforcer G6 DD, it needs to be fine tuned, to provide precise steering response and improve grip when cornering, so you don't slide off the track. Small changes can make huge advancements and our easy to understand guide will help you to the optimum Set-up for your individual driving style.

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ Custom Works Enforcer G6 DD - 0930 Chassis ★

Buying a Used Custom Works Enforcer G6 DD
Sprint Car (and What to look for)

There are essentially three reasons you might want to buy a used Custom Works Enforcer G6 Electric Sprint Car; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Custom Works website, or purchased separately on eBay. With an instruction manual, any problems with your model Sprint Car you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Custom Works Sprint Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Custom Works models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Custom Works Enforcer G6 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Enforcer G6 model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your Enforcer G6 Sprint Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

The gearbox of your used Sprint Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Sprint Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Sprint Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Electric Sprint Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The Enforcer G6 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Custom Works Enforcer G6 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Custom Works Sprint Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your Enforcer G6 model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Bumpsteer

   In plain language, Bumpsteer is exactly what it sounds like. If your car goes over a bump, it will affect the toe-in setting and can on some tracks make handling of the car in a straight line difficult.

   To check if your car might have any problems with bumpsteer, have it in race mode, with the motor and battery etc in position. Place the car on a flat surface and push down your car at the front. Looking down from above, keep a close eye on the wheels and watch for any angular movement to the side. If there is then you have bumpsteer.

   For off road cars, because of them having longer dampers in comparison to on road, a small amount of toe out is considered by many as acceptable in the lower position and can sometimes be used as a tuning option because of its aggressive effect on turning ability when entering corners. On road cars, because of the shorter damper movement and the greater need for precise steering and stability in a straight line, generally have less of a problem. However if bumpsteer is detected, drivers generally try to eliminate this as much as possible.

Read the Complete Article ▶ ▶

Hints, Tips and Information

The Importance of Balancing your Model Car Wheels

   The day I passed my driving test at the young age of 17, the first thing I did was to drive over to my girlfriends house and take her out to a long straight stretch of road close by, where the boy racers would often congregate. No one was around that day, so the road was relatively quiet. I slowly went through the gears and we were soon up to 65 with no problems, but as we got closer to 70, my hands began to sense a small vibration on the steering wheel. By the time we hit 75, the steering wheel and the whole car was vibrating wildly. My girlfriend was hysterical, screaming for me to "slow down!" I did of course and tried to calm her down.

   Back home I told my dad what had happened. He then reminded me that just the week before we had put on a new set of front tires and suggested the wheels were probably out of balance. Sure enough, after the wheels were re-balanced, at 85, 90, the car was steady as a rock and drove perfectly.

   As I got deeper into RC, that memory returned and I realised to be more competitive I would have to balance all my wheels.

How I Balanced my Model Car Wheels

Wheel balancing equipment for RC cars is now available on line and from most RC model shops, but back then I had to make my own using the rear end of an old Tamiya F1 car.

Read the Complete Article ▶ ▶