Radio Controlled Models
Share RCScrapyard on Facebook
RCScrapyard Radio Controlled Models
Flags
RCScrapyard.net contains Google and Amazon Affiliate links, which may earn us commission. See our Disclosure page for more info.
bar

1/10 Scale Electric Truck/Truggy:

Team Associated ProSC10 AE Team RTR - 70016 / 70016C - Radio Controlled Model



History and Info:

   Released by Team Associated in 2018, the ProSC10 AE Team RTR Short Course Truck - # 70016 - sourced a number of its parts from the RC10SC5M . The package includes a Reedy Brushless Motor, ESC, steering Servo and DVC (Dynamic Vehicle Control) 2.4Ghz Radio system.

   A Combo version - # 70016C - was also introduced, with all of the above plus a Reedy LiPo Battery and Reedy balance Charger.

   The 4WD ProSC10 is shaft driven on a molded composite chassis, with gear type differentials, coil spring over oil filled dampers, rear dogbones with front CVA universal joint drive-shafts, slipper clutch and a full set of ball bearings.

Team Associated ProSC10 AE Team RTR

▼ Scroll Down for More Images ▼


   To get the best from the Team Associated ProSC10, it needs to be fine tuned, to provide precise steering response and improve grip when cornering, so you don't slide off the track. Small changes can make huge advancements and our easy to understand guide will help you to the optimum Set-up for your individual driving style.


Model Versions:

  • #70016 ProSC10 AE Team RTR
  • #70016C ProSC10 AE Team RTR LiPo Combo

Features:

  • Based on the 9-time R.O.A.R. National Champion short-course race truck platform
  • 2.4GHz 2-channel radio with new DVC (Dynamic Vehicle Control) receiver featuring built-in adjustable gyro
  • High-torque, metal-gear Reedy Servo with spring style servo saver
  • Powerful Reedy 3300kV brushless motor
  • Water-resistant high-power Reedy brushless speed control with T-plug connector and LiPo low voltage cutoff
  • Factory-finished short-course racing truck body
  • Water-resistant enclosed receiver box
  • Durable and lightweight aluminum top shaft
  • Low center-of-gravity molded composite chassis with hook-and-loop battery straps that accommodate both NiMH and 2/3s LiPo battery packs
  • Metric hardware throughout
  • 14 precision rubber-sealed ball bearings
  • Durable front and rear body mounts
  • Rear CVA drive shafts for more reliability
  • Aluminum 12mm big bore coil-over shock absorbers
  • 2.6:1 ratio gearbox with heavy-duty sealed gear differential and externally adjustable V2 slipper clutch
  • Rugged steel turnbuckles for adjustable camber and front toe-in
  • Fully adjustable suspension geometry
  • Vertical ball ends for roll center adjustments, front and rear
  • Many Factory Team options already available!
  • Combo #70016C includes a Reedy Compact Balance Charger and Reedy 7.4V LiPo Battery with T-plug

(Source: Media Press Release)







Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors















Flags
★ Team Associated ProSC10 ★
Team Associated ProSC10
★ Team Associated ProSC10 Chassis ★
Team Associated ProSC10 Chassis
★ Team Associated ProSC10 Chassis ★
Team Associated ProSC10 Chassis
★ Team Associated ProSC10 DVC Receiver ★
Team Associated ProSC10 DVC Receiver
★ Team Associated ProSC10 Radio, Motor, ESC and Servo ★
Team Associated ProSC10 Radio, Motor, ESC and Servo
★ Team Associated ProSC10 Gear Differential ★
Team Associated ProSC10 Gear Differential
★ Team Associated ProSC10 Shocks ★
Team Associated ProSC10 Shocks

Buying a Used Team Associated ProSC10
Truck (and What to look for)


   There are essentially three reasons you might want to buy a used Team Associated ProSC10 Electric Truck; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

   Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Associated website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
   When you receive your used Team Associated Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Team Associated models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

   If the body shell of your Team Associated ProSC10 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your ProSC10 model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your ProSC10 Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

   The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Spur Gears
   Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

   Ball joints always cause problems. For top level Electric Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
   The ProSC10 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

   If body roll on your Team Associated ProSC10 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

Ball Bearings
   If your used Team Associated Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your ProSC10 model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^












Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.



















Hints, Tips and Information

Bearing Seals

   If you were to ask anyone with a modicum of experience in RC, they will tell you that the best modification you can make to a basic RC model, is to add a set of ball bearings.

   Quite a few of the entrance level models at the time this article was written, come with plastic and sintered brass ring type bearings. If these bearings are installed in the model and coated with grease as advised in the car manual, dust and grit can be caught in that grease and be dragged into the bearing where it can abrade the shaft that spins in it and it won't be long before it becomes a very sloppy fit, causing all kinds of problems.

   But what should you look for when buying bearings? There are a number of types of seal used on ball bearings, and there is much debate concerning which is the best for RC.

Read the Complete Article  ▶ ▶






Hints, Tips and Information

Roll Center

   One of the least understood settings on RC model cars is concept of roll center. The simple definition of roll center is a point in space that the chassis rolls from side to side as the car maneuvers around a corner.

   To calculate roll center you have to consider things like the height of the axles, the inside and outside camber link positioning, the length of the suspension arms and the location of their inside pivot point. Sounds complicated doesn't it - and in truth - it is.

   On all RC model cars, most of the cars weight is above the chassis and the center of gravity of the car is not only from front to rear, but also from top to bottom. This point is called the "true" center of gravity and is the point around which the weight of the car will want to roll from side to side, but it is the roll center of the chassis that the chassis will actually roll around, not the center of gravity.

   Once you have determined the positions of roll center and center of gravity, you can calculate the "roll moment". It is this that determines how easily the chassis will roll from side to side.

The Effect of Roll Center on your Car

   But what does all this mean? I hear you ask. Well, it gives you some insight to what changing the position of your camber links can do to the way your car handles.

Read the Complete Article  ▶ ▶







RC Models:
Radio
& Motors:
Other
Accessories: