1/8 Scale Electric Rally/Touring Car:

Capricorn LAB C803 EP Race Evo (Radio Controlled Model Review)

Navigation:

History and Info:

Introduced by Capricorn RC circa 2019, the LAB-C803 EP Race Evo Electric Powered Touring Car Chassis, was based on the Nitro C803 Evo and was designed to accept either two 3S or two 2S square-type LiPo battery packs or use a 6S or 4S conversion kit. The model was available as an assembly Kit, requiring a Radio System, motor, ESC, battery, charger, servo and a Lexan bodyshell to be purchased separately.

The 4WD model is Belt Driven, on a carbon double deck chassis, with red anodised alloy parts, rear fixed axle with dogbones, front one-way axle with universal joint drive-shafts, coil spring over oil filled dampers, rear anti-roll bar, servo-saver and ball bearings.

Capricorn LAB C803 EP Race Evo On-Road

▼ Scroll Down for More Images ▼

To get the best from the Capricorn LAB C803 EP Race Evo, it needs to be fine tuned, to provide precise steering response and improve grip when cornering, so you don't slide off the track. Small changes can make huge advancements and our easy to understand guide will help you to the optimum Set-up for your individual driving style.

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ Capricorn LAB C803 EP Race Evo Chassis ★

Buying a Used Capricorn LAB C803 EP Race Evo
Touring Car (and What to look for)

There are essentially three reasons you might want to buy a used Capricorn LAB C803 EP Race Evo Electric Touring Car; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Capricorn RC website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Capricorn Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Capricorn models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Capricorn LAB C803 EP Race Evo is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your LAB C803 EP Race Evo model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your LAB C803 EP Race Evo Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Engine mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The LAB C803 EP Race Evo steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Capricorn LAB C803 EP Race Evo is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Capricorn Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your LAB C803 EP Race Evo model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued and Listed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Make your RC Model Ball Bearings Work for You

   If you are serious about your racing, looking after your bearings is essential if you are to remain competitive.
   My own experience is in both Off and On Road, National and International Car racing, but most of these tips could be useful to all forms of RC.

   Shields: The main problem with Ball Bearing Shields is they create friction, and obviously the more you can reduce friction, the more efficient your bearings will be, so here's a tip that does just that.
   Wheel Bearings always come in pairs, positioned side by side. If you think about it, the two inside shields on each bearing are not required, so ... you can remove them using a small jewelers screwdriver ... simple. And in one fell swoop you have halved your wheel bearing friction.

Read the Complete Article ▶ ▶

Hints, Tips and Information

Keeping Notes

   If all you will ever do is go racing at your local track every week, then this article is not for you. However, if you ever look towards travelling around to different tracks around the country, or even the world, the value of keeping notes is all too obvious.

   Every time I raced in a regional or national competition meeting, I would make detailed notes, aided by a little local knowledge initially, and later fine tuned to suit my own driving style.

   My experience now means there are few, if any outdoor tarmac tracks within a 300 mile radius I haven't been to, and my notes on motor, gearing, camber angles, shock settings, tire choice and what inserts work best for that particular track, amongst others, allow me to save valuable time on the finer points of car setup, that can be done in the warmth of my own home on the kitchen table days before the meeting, instead of the often crippling heat, or the arduous conditions inside a wind blown tent.

Read the Complete Article ▶ ▶