1/18 Scale Electric Buggy:

Team Associated Reflex 1:18 Buggy RTR - 20109 - Radio Controlled Model

Navigation:

History and Info:

Introduced by Team Associated in 2016, the "Qualifier Series" 4WD Reflex 1:18 Buggy RTR - # 20109 - was based on the same chassis as the Rival 1:18 Monster Truck and Apex 1:18 Touring Car and was available with either a black or white pre-painted bodyshell. The pre-assembled Ready to Run model came with Super 370 motor, ESC, battery, charger and XP radio system.

The model is shaft driven, on a molded plastic chassis, with ball differentials, coil spring over oil filled dampers, dogbone drive-shafts and a full set of ball bearings.

Team Associated Reflex 1:18 Buggy RTR

▼ Scroll Down for More Images ▼

To get the best from the Team Associated Reflex, it needs to be fine tuned, to provide precise steering response and improve grip when cornering, so you don't slide off the track. Small changes can make huge advancements and our easy to understand guide will help you to the optimum Set-up for your individual driving style.

Model Version:

#20109 Reflex 1:18 Buggy - RTR

Features:

The REFLEX 1:18 transfers all the power to the ground with its efficient, shaft-driven, 4WD powertrain featuring adjustable ball differentials front and rear
The REFLEX 1:18 suspension absorbs all of the bumps and jumps in the dirt with fluid-filled shocks for smooth and consistent dampening
The four lower suspension arms are symmetrical and work with the molded upper suspension links to ensure that the Reflex 1:18's suspension geometry is optimized from the start
Team Associated's XP radio and Reedy Powered series electronics installed in the REFLEX 1:18 are compact and easy to use while providing high performance. A 10-hour wall charger is included
White or Black REFLEX buggy body designs to choose from, with sleek graphics applied

(Source: Media Press Release)

Reflex 1:18 Buggy - 20109
Manual

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ Team Associated Reflex 1:18 Buggy Box ★

Team Associated Reflex 1:18 Buggy RTR Box

★ Team Associated Reflex 1:18 Buggy RTR in White ★

Team Associated Reflex 1:18 Buggy RTR Body

★ Team Associated Reflex 1:18 Buggy RTR Chassis ★

Buying a Used Team Associated Reflex
Buggy (and What to look for)

There are essentially three reasons you might want to buy a used Team Associated Reflex Electric Buggy; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Associated website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Team Associated Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Team Associated models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Team Associated Reflex is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Reflex model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your Reflex Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

The gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Electric Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The Reflex steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Team Associated Reflex is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Team Associated Buggy comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your Reflex model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Rechargeable Batteries
for RC Models

   At the time this article was written, there are four types of Rechargeable Batteries that are commonly in use for Radio Controlled Models.
Ni-Cad (Nickel Cadmium) Batteries have been around the longest. My first stick battery, purchased way back in 1987 was rated at 1200Mah (Mili Amp Hours) and with a silver can 27 Turn motor my Tamiya Boomerang would run around in the back yard for a good seven minutes before slowly coming to a stop. Ni-Cad development continued until around 1998 to a maximum rating of around 2000Mah and matchers pack builders and battery technicians were able to put together six cell packs with voltages approaching 7.4 Volts, to give those that could afford them, an edge over the rest.

   Ni-Mh (Nickel Metal Hydride) Batteries came along in the late 1990s, and by the year 2000 were available at ratings up to 3000Mah. Again, matchers and pack builders worked hard to provide the ardent racer with packs to provide that little bit of extra power, and ESC manufacturers also chipped in with improved controllers to take full advantage of this new technology.

   Now the problem wasn't gearing the car to get to the end of the race using the available battery power, but to find the brushed motor that could handle gear setting that provided the speed and acceleration without the motor overheating and wearing the commutator too much so it needed a skim after every 2 runs. My favourite at that time was the 9 Double.

   More recently, Li-Po (Lithium-Polymer) Batteries have appeared on the scene, providing are a huge step forward in performance when compared with Ni-Cad and Ni-Mh batteries.

Read the Complete Article ▶ ▶

Hints, Tips and Information

How to put on Decals

   After spending lots of time and effort to paint your bodyshell, you come to the point where you make it look good by putting on all those flashy decals, but before you rush in with the scissors and start cutting, there are a few things you should do first.

   Good preparation is key to a perfect job, so before you do anything with your decals, you must first of all wash your hands, and then make sure the bodyshell is clean and no oil or grime from your previously grubby fingers remains on the Polycarbonate Lexan surface. Methylated spirits is the thing to use, or failing that, use one of those wipes you use for your computer monitor screen.

   As the body shell dries, you can carefully cut out the decals from the sheet. Do the big ones first and leave the smallest ones for last.

Read the Complete Article ▶ ▶