1/10 Scale Nitro Truck/Truggy:

Traxxas Jato 3.3 (2014) - 55077 - Radio Controlled Model

Navigation:

History and Info:

   Introduced by Traxxas in 2014, the Jato 3.3 Stadium Truck - # 55077 - was upgraded with a TQi 2.4Ghz Radio System with Link, and Factory installed Telemetry Sensors, and came factory assembled RTR, with a choice of four pre-painted ProGraphix Bodyshells, TRX-3.3 Racing Engine with EZ-Start and Anaconda Performance Tires.

   For other Jato versions, Check out our Traxxas Archive.

   The 2WD model is based on a blue anodised 3mm alloy plate chassis, with 2-speed transmission, a sealed gear type differential, coil spring over oil filled dampers, sway-bars, slipper-clutch, sealed universal joint drive-shafts, a full set of ball bearings and wheelie-bar.

Traxxas Jato 3.3 Truck - 55077

▼ Scroll Down for More Images ▼

To get the best from the Traxxas Jato 3.3, it needs to be fine tuned, to provide precise steering response and improve grip when cornering, so you don't slide off the track. Small changes can make huge advancements and our easy to understand guide will help you to the optimum Set-up for your individual driving style.

Jato 3.3 (2014) - 55077
Exploded Views

Jato 3.3 (2014) - 55077
Parts Lists

CHECK AVAILABILITY
On Amazon

Radio Controlled Model Accessories:

★ Traxxas Jato 3.3 ★

★ Traxxas Jato 3.3 Chassis ★

★ Traxxas TQi 2.4Ghz Transmitter with Bluetooth and TRX-3.3 Engine ★

Buying a Used Traxxas Jato 3.3
Truck (and What to look for)

There are essentially three reasons you might want to buy a used Traxxas Jato 3.3 Nitro Truck; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Traxxas website, or purchased separately on eBay. With an instruction manual, any problems with your model Truck you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
When you receive your used Traxxas Truck, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

Next, for those Traxxas models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

If the body shell of your Traxxas Jato 3.3 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Jato 3.3 model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

If you intend to race your Jato 3.3 Truck model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

The gearbox of your used Truck should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Truck at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Gears are a weakness on all Truck RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

Ball joints always cause problems. For top level Nitro Truck racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
The Jato 3.3 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

If body roll on your Traxxas Jato 3.3 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

If your used Traxxas Truck comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

Finally, good luck with your Jato 3.3 model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^

Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.

RC Information and Advice:

Hints, Tips and Information

Sway Bars

   On most forms of RC model cars, Sway Bars, also referred to as Stabilizers, Torsion Bars, or more commonly in some parts as Anti Roll Bars, are often nothing more than a short length of spring steel, clamped to the chassis or sometimes the gearbox of the car, extending out to the lower wishbones direct or connected to the wishbones using short adjustable or fixed length links and ball joints, depending on their position.

   The principal behind the Sway Bar is simple. As the car enters a corner, weight is transferred to the outside wheels, the chassis rolls due to inertia and the suspension dips and grip on the inside wheels is reduced. In an effort to counter this dipping effect and transfer some grip back to the inside wheels to improve traction as you exit the corner, the sway bars transfer the dip of the outside, to pull down the inside wishbones, improving grip on the outside wheels and improving overall stability.

   Sounds complicated I know, but for some tracks sway bars can be a useful tool when you have exhausted all other options to correct your handling problems.

   Tuning your Sway Bars is quite easy.

Read the Complete Article ▶ ▶

Hints, Tips and Information

Glow Plugs for Nitro Engines

   Nitro Engines for RC Models use a system to ignite the fuel mixture that simply employs a wire coil in a small housing called a Glow Plug. To start the engine, a battery powered Starter, or Glow Igniter, is connected to the Glow Plug and electric current heats the coil to white hot, so that when you pull start your engine, the air - fuel mixture in the cylinder is ignited. With the engine now running, the starter is no longer required. Heat generated under compression is enough to keep the coil element hot enough to keep the engine running.

   At some point, the Glow Plug originally supplied with your Engine will invariably burn out. To test your Glow Plug, remove it from the cylinder head and place it in the igniter. If the coil instantly glows bright orange, the plug is healthy, a weak or no glow at all, indicates probable burn out.

   If your engine isn't too old you should be able to obtain a replacement, but if the manufacturer is no longer in business you may have a problem.

Read the Complete Article ▶ ▶